Quick Program Guide for FC-7448

Meian tech Focus brand wireless smart home automatic burglar alarm, emergency alarm, remote monitor system for home security. How to program the wireless alarm system? Learn it here.
Posts: 835
Joined: Wed Dec 05, 2018 12:27 am

Quick Program Guide for FC-7448

Unread post by vedard »

1.Enter Programming mode by pressing 9876#0, (password +#0) then power LED and arm/disarm LED flash simultaneously, LCD display Prg:Mode4.05 Adr=
Exit Programming: Press “*” for 4s till “di” sound

2.Arm: press 1234(password) and “arm/disarm” button
3.Disarm: Press 1234(password) and “arm/disarm” button, LED of “arm/disarm” will be off
4.Force Arm: Press 1234(password) and “arm” + “bypass” buttons
5.Bypass: Press 1234(password) and “bypass”+xxx(zone No. with 3 digits)
6.Add user’s No. and password: press 1234#0, press “0”, then user No.(001-200), enter authority level(0-6) with “#”, then enter 4 digits password with “#”, password with “#” again.
7.Delete user id: Press 1234#0, press “0”, then user No.(001-200), enter user authority (0-6) with “#”, press 0#
8.Programming address:
0001-0030 is zone function program address
0031-0278 is zone program address
0415-0538 is zone features program address

9.How to fill in data:
The program address is 4 digits and value of address is 2 digits. After enter programming, LCD display Prog Mode 4.05 Adr= , Fill in “Adr=” with 4 digits program address. Then input 21#, then the two digits will be displayed alternately. Press “#”, it will display “1”, press “#” again, it will display “2”.(It is default and can be changed by programming), then skip to next program address. If you need to program some address, just press”*” twice and it will return to Prog Mode 4.05 Adr=
Note: FC-7448 is shipped from the factory as a working, pre-programmed control. Many of the programming address may already be set to the values you need. The default values are shown in Reverse Print. You don’t need to pre-program this address.

10.Program zone function (address is 0001—0030)
Zone function means the zone is delay zone, instant zone, 24 hours zone etc. It is already programmed into the panel but you can change the default and add new zone function according to user’s manual.

11.Zone programming (address is 0031—0278)
0031 means the first zone, 0032 is the second one and so on. If you want to set the eighth zone as 24 hours zone, then you need to change the value of this address to “07” and press # to confirm.
Note: This part is required to program according to requirement.

12.Cancel zone No.
Press 9876#0
Enter 0039(the ninth zone for example)
Enter 00# (the zone attribute will be cancelled)

13.Return to factory default
Press 9876#0
Enter 4058(return to default address)
Enter 01# to confirm

14. Alarm Telephone program and CID communication programming
Press 1234#0 to enter
Enter 9876#0
Enter 3159 (program address 3159, 3175, 3191 for 3 group alarm telephone)
Enter xxxxxxxxxxxxxxxx (max 16 digits telephone No.) with # to confirm

Determine Telecom Format
Press 9876#0
Enter 3157 (telecom format program address)
Enter 91 (Contact ID)

Program user’s code
Press 9876#0
Enter 3429
Enter 1230(user’s code is 123 for example, and need to add 0)

Alarm Report Programming
Press 9876#0
Enter 3153(program address)
Enter 11#

Program telephone dialing times
Press 9876#0
Enter 3154(program address)
Enter 12# (dial twice for example)

15.Control Panel time setting and arm/disarm timer program
Press 1234#0 + “2” to set date
Press 1234#0 + “6” to set time
Press 1234#0 + “1” to set auto arm time for every day
Press 1234#0 + “4” to set auto disarm time for every day

Remark: Please use 2.2K resistant for FC-7448 8 wired zones and use 47K resistant for expand module.
Authority grade is: 0 super user, 1 unlimited user, 2 combined user, 3 arm user 4 temporal user, 5 duress user, 6 entrance user
bus type security system wiring
bus type security system wiring
7448 wiring.JPG (83.11 KiB) Viewed 4944 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Posts: 835
Joined: Wed Dec 05, 2018 12:27 am

Troubleshooting for FC-7448 bus-line alarm system

Unread post by vedard »

FC-7448 is professional grade commercial security system. It requires security service installation and maintenance.
There may be some malfunctions with the equipment during working period. How can we troubleshoot it? Below we list some common
malfunctions and help troubleshooting it.
1. The system showed "System fault"
Solution: Enter password "#87" to query. It showed system fault and no connection to backup battery. Correctly connect backup battery
to the alarm host and the trouble solved. If not need backup battery, the fault can be ignored and the security system can work normally.

2. FC-7448 showed "communication fault". There are some possible causes. a. The connection between the host and the keyboard is incorrect or bad.
b. The main keyboard is not correctly set with DIP switch, or the other keyboard is not programmed. 3. Hardware failure can also cause this problem.

3. FC-7448 showed "zone is not ready":Enter password "#87" to query. It showed zone fault. 1. Check corresponding zone module FC-7401 connection is good or not.
2. Check corresponding zone module FC-7401 DIP switch setting is correct or not. If not zone fault. 1. Check connection between zone module FC-7401 and detector is good or not.
2. Check whether or not the detector is triggering alarm cause intrusion detected in detection area.
3. Check the EOL resistor value is correct or not and connection is good or bad.
More information such as How to install and debug FC-7448 Commercial Security Alarm System can be found at http://blog.vedardalarm.com/install-deb ... arm-system
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Posts: 88
Joined: Sat Oct 31, 2020 1:01 pm

FC-7448 for large scale anti-theft security solution

Unread post by Jim »

FC-7448 bus-type alarm host is a large scale security system with excellent performance, powerful function, easy operation and reliability.
FC-7448 is widely used for perimeter security, office building.
FC-7448 adopts dual bus system and alarm management software for users to set up a commercial and industry security alarm linkage system with police alarm center, patrol and security.
This system can be equipped with multiple functions such as multiple defense zones, patrol, perimeter defense. It can be connected with FC-7401, FC-7408 modules and extended keyboards to expand the defense zone and realize the multiple defense zone detection of the entire building. The partition contains floors that can be managed uniformly. Use the LCD keyboard of the host to arm, disarm and cancel the alarm. All operating information and alarm information are sent to the security center management software in real time. And the electronic map of the alarm area can be automatically displayed.
The patrol system and the alarm system are integrated. FC-7448 defense zone is connected to the patrol switch as a 24 hours invisible defense zone. At the security software part, the defense zone is defined as a patrol defense zone, so the patrol status can be displayed on the real time. The system can define patrol routine freely, automatically start multiple patrol lines at regular intervals, or manually start patrol lines, and can prompt timely patrols, untimely patrol, payrol advances, patrol etror triggers and other information.
For the alarm linkage, two solutions are provided. One is software linkage type. We provide the software interface of the security center through the cooresonding API function transmitting alarm information to the management system of the superior BA through the local area network. Another in hardware linkage. With FC-32B of 32 relay output module connected to the alarm information through the contact BA system DI capture board. a FC-7448 hosts can be connected. In actual use, the hard linkage scheme is easier to implement and signal response speed is faster.
Guide and supplier for fire alarm systems.
Posts: 88
Joined: Sat Oct 31, 2020 1:01 pm

FC-7448 security system configuration

Unread post by Jim »

FC-7448 works as security alarm control part. All detectors' signals are concentrated on the host, the host them process the signals and transmits to the PC.
One LCD keypad FC-7216 bus driver is configured with each host. The host must expand the bus defense zone. The bus interface is on the driver.
LCD keypad FC-7216 is used to program and debug the alarm host and security system.
FC-7408 is 8 zone exander can be connected with the alarm host to connect 8 defense zones. The module needs to be powered. Serial communication module FC-7412 is equipped with the alarm host. This module provides the host eith a standdard RS232 interface to transmit information.
Other devices should be equipped.
1. Alarm management software.
2. Several emergency bittons.
3. Patrol buttons
4. Power supply several 12v and FC-7408 expansion module power supply.
5. Serial expander connected with FC-7412
6. 32 relay module FC-32B 12/32 relay output module to link with BA system. Maximum 4pcs can be equipped to each host.
7. PC computer
8. printer.
Guide and supplier for fire alarm systems.
Posts: 835
Joined: Wed Dec 05, 2018 12:27 am

Re: Quick Program Guide for FC-7448

Unread post by vedard »

Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Post Reply