Video guidance for installing fire alarm system

Fire alarm system manual download for studying addressable intelligent alarm contorl panel, fire detection system, fire warning, fire evacuation system.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Video guidance for installing fire alarm system

Unread post by vedard »

How to program addressable fire alarm detectors?
Using hand-held programmer to encode smoke detector, heat detector, gas sensor, manual call point etc.
IMG_5284.MP4
(9.94 MiB) Downloaded 380 times
Attachments
F6DC5B38-8EA8-450A-B381-E1730CD226F8.jpeg
F6DC5B38-8EA8-450A-B381-E1730CD226F8.jpeg (206.57 KiB) Viewed 4141 times
101EB612-F01C-47FD-A92A-54AD8EBBEB85.png
101EB612-F01C-47FD-A92A-54AD8EBBEB85.png (100.49 KiB) Viewed 4141 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

How to replace fire floor display panel and detectors

Unread post by vedard »

After inspection, we found some smoke detectors, heat sensors, fire floor display panel and manual call point are fault. How to replace the addressable fire alarm system component?
Firstly, we need to check the addressable panel brand and contact fire alarm system manufacturer or distributor. We need to shop new detectors, fire floor display panel and others. If we still have spare parts, we can use them.
If we need to shop new addressable fire component, we need to make sure to shop the old addressable fire alarm panel compatible detectors. So, it is better to contact manufacturer and check.
We need to buy addressable fire alarm system programmer or use the old one if it is available.
Then, we need to check and make note of the fault detectors, fire floor display panel. Make note of the address code and description. After that, we will program the new corresponding detectors and components. At last, we install the new detectors and fire alarm floor display panel.
Find and shop the professional fire alarm system at Vedardsecurity store.
Video guidance at https://www.youtube.com/watch?v=NOqAZkDbXbg
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

How to set up electric fire monitor detector

Unread post by vedard »

Electric fire monitoring system can effectly stop fire occurance. It is sub-system of fire alarm system. It is early warning system of fire. Before fire occurs, it can find the electric fault and high temperature of leakage current.
The combined electric fire monitor detector is installed in electric distribution box. It wires residual current detectors for current leakage detection, it wires temperature detector for high temperature detection. The alarm value can be set at the electric fire monitor detector. The output can be set to cut off circuit power supply.
The electric fire monitor can work independently or work with addressable fire alarm system.
Shop complete electric fire monitor components at vedardsecurity shop.
Learn how to set up electric fire monitoring system at https://www.youtube.com/watch?v=bGVv8ZHmCDs
set up electric fire monitor system.mp4
(12.93 MiB) Downloaded 301 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Enable to receive fire alarm from mobile

Unread post by vedard »

The earlier a fire alarm is received, the less people will die. The more people who receive early warning of fire, the less loss of life and property.
How can people receive fire signals directly at the first time?
Set the fire alarm signal to send to the mobile phone. The building manager, the building's fire chief should be responsible for responding to fire signals in a timely manner.
How to set mobile phone in intelligent fire alarm panel? The new addressable fire alarm panel TC-5109 has the function of mobile phone setting. At setting menu, input mobile phone number, when fire alarm triggers, the mobile will receive fire alarm or fire fault information.
Watch it at youtube https://www.youtube.com/shorts/_OUV9_ZrYX4
Attachments
set mobile phone number in fire alarm host.mp4
(3.06 MiB) Downloaded 294 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

2-wire, 4-wire or 6-wire fire hydrant button

Unread post by vedard »

There are 2 wires and 4 wires or 6 wires fire hydrant button. What is the difference? Why are there different wiring types of fire hydrant?
For 2 wires fire hydrant button, you just need to wire the 2 wires to the fire alarm control panel.
For 4 wires, there are 2 wires signal lines and need to wire to fire alarm control panel. And other two wires are fire bump starting lines. You need to wire it with fire bump.
For 6 wires, except two lines are signal lines, two lines are pump starting lines, and the other two lines are feedback lines. The feedback lines is connected with bump starting indicator lamp and it will light up the LED indicator when fire bump is started.
Actually, the 2 wires fire hydrant button is new one. And the 4 wire or 6 wires fire hydrant button is old one. When the fire hydrant button connect with fire bump directly, it will start the fire bump directly. And that may mis-start the fire bump and cause loss.
So, fire bump will not be activated by fire hydrant directly. It will be activated by fire alarm control panel with logic judgement. Only after receiving of both alarm signals from hydrant and same fire zone smoke detector, it will activate the fire bump. Or it will activate the fire bump after receiving both hydrant and manual call point alarm signals.
Video is available at https://www.youtube.com/watch?v=oStJ5k6OfCQ
improvement of fire hydrant button.mp4
(15.72 MiB) Downloaded 300 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Video guidance for installing fire alarm system

Unread post by vedard »

How to connect the combustible gas detector with gas monitor panel?
We take example of conventional gas monitor panel and explosion proof gas detector as example.
The explosion-proof gas detector should be used in chemical factory, oil field industry, and stocks with potential combustible gas and toxic gas such as SO2, H2.
The gas detector has LCD monitor and sound and light warning devices equipped. From the monitor panel, you can get alarm and exact value of the leaked gas.
View the video of connecting explosion proof gas and gas monitor panel at
https://www.youtube.com/shorts/aDkxXmt4WIg
connection of combustible gas and alarm host.mp4
(41.8 MiB) Downloaded 315 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Video guidance for installing fire alarm system

Unread post by vedard »

Installing fire alarm system easy with video guidance.
Learn how to install fire alarm system at vedard.com/forum
Shop fire alarm system at fire alarm store online.
Harmful gas monitoring and control is important part of security system for industry security. Automatic gas controller solenoid, exhaust fan will be started with programming after gas leakage is detected.
The gas monitor and control system is easy to wire and program with a few steps.
1. Wire the gas monitor control panel with explosion-proof gas detectors.
2. Wire the exhaust fan with the gas monitor control panel.
3. Wire the solenoid valve with the gas monitor control panel.
4. Set the alarm high value and low value of the gas leakage concentration.
5. Set the linkage device for the detector.
6. You can bypass the detector if there is fault.
7. You can query the alarm and system information.
8. The system has self check function.
9. You can connect the alarm monitor system to central fire security monitor system.
Learn how to wire and program combustible gas, toxic gas leakage monitor and control system at
https://www.youtube.com/watch?v=quaf0fSBIpg
gas leakage monitor.JPG
gas leakage monitor.JPG (76.97 KiB) Viewed 3936 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Video guidance for installing fire alarm system

Unread post by vedard »

Where is gas fire extinguishing system used and how important is it? In some areas where water extinguishing is not suitable, gas extinguishing systems are required.
How will the gas fire extinguishing system work? Automatic fire extinguishing system consists of fire detector and gas extinguishing system. When a fire is detected, the fire control sends out an alarm signal in the first stage and turns on the audible and visual alarm in the fire protection area.
When other detectors, such as heat detectors or manual alarm buttons, also give an alarm, the fire extinguishing system will give a second stage alarm and turn on the sound and light alarm outside the protection zone. At the same time, the gas fire extinguishing will be started after a delay of 30 seconds.
Is there harm to human body and equipment by gas fire extinguishing? What should we pay attention to? Gas extinguishing does no harm to equipment. But it is harmful to human body. Therefore, gas fire extinguishing has manual and mechanical starting modes and can be selected according to whether there is a person in the fire area.
gas fire extinguishing.JPG
gas fire extinguishing.JPG (69.32 KiB) Viewed 3464 times
Video guide for gas fire extinguishing system.
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Fire manual call point push button installation video demo

Unread post by vedard »

Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Post Reply