Questions of solar power wireless perimeter security system

Perimeter Security system wireless solar power photoelectric beam system installing instruction. Video guidance and user manual for setting up solar power beam system for outdoor yard, wall, balcony security protection.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Questions of solar power wireless perimeter security system

Unread post by vedard »

FAQ for HB solar power wireless beam sensor, perimeter security systems
1. How many zones can connect to panel?
For the moment ,we have 9 sets of host unit ,least one support 4 defense zones, most one can be up to 1000 zones. If you wanna more zones, we can make according to your requirement.
2. Are your devices functional in low temperature (-2 to 15 degrees) in winter time, (17 to 35 degrees) during summer time?
Our detector supported working temperature range :-30C~70C.
We have been sold this product more than 10 years, we have long-term partner in bad weather countries such as Russia、Africa.
3. Are these solar alarms compatible with ademco alarm systems? We total have 9 sets of alarm host:
Ademco available:HB-BJQ560-A; HB-BJQ560-B; HB-2020C;HB-3030C;HB-G250. Ademco unavailable: HB-MFR;HB-2020A;HB-3030A, GSM or TCP/IP network available HB-4040/5050/2050 app alarm panel
4. what distances can products achieve?
There are three types solar power intrusion detectors. Beam series detection distance is 100m. Grating series detection distance is 10m, garden series detection distance is 50m. PIR series detection is 8-10m. All series wireless RF transmission distance is 500-1000m.
5. What is the lifespan of the standby battery?
The lifespan of the battery is more than 10 years.
Firstly,Our battery is LFP battery ,its cycle recharge time is 2000 times.
Secondly,the capacity of the battery is 500mAh, while standby current consume only 0.5mAh,the sensors can normally work more than 15days without solar charging.
So we can got: 2000times (LFP battery cycle recharge time)X15days(standby time)=30000days(about 82 years),deduct any other factors,10 years is available.
6.I need to know how to match the beams with each type of system and how they work?
 Firstly: turn on the sensors
 Secondly: set the alarm host into coding status
 Thirdly: trigger the sensor, so the alarm host can remember the sensor
7. is there a signal repeater HB-ZFQ with solar panel?
For the moment, we don’t have solar wireless signal repeater.If that’s necessary to your project, we’ll provide a solar powered device for the repeater.
8. What is the mechanism your system uses in order to detect stealing of sensors or jammer the signal in order to tamper the system?
Firstly, the working principle of our sensors is Active infrared detecting, so if any terminal is moved or damaged, sensors will report to host at once. Same time,host will indicate abnormity (e.g. alarming ,invalid , light interference).
Secondly ,the wireless transmission technology we made is FSK + FHSS technology,it has strong ability to anti-interference.( e.g. once sensor was Triggered), it will send 3 signals to host (3 different frequency points),and host can receive these signals independently. This anti-interference technology makes our products more competitive in same line.
9. the wireless is APPROVED for Canada? What frequency is it? And how far will it work?
Our products was certificated by FCC and CE, and we have many regular Canadian customers, its standard for Canadian frequency.
The sensors adopt 433MHz(FSK + FHSS) transmission technology,that to say once sensor was triggered ,it will send three signals(different frequency points) to host. and host can receive these signals independently. This anti-interference technology makes our products more competitive in same line.
10. Do they check status with the sensors , like a test signal? How often?
Our solar sensors will self-check every 2 minutes, if any problem (e.g. low-battery、invalid、 light interference etc.) ,Sensors will immediately report to host.
11. Do your sensors have anti-masking features?
The sensors adopt FSK + FHSS technology,it has strong ability to anti-interference. i.e. once sensor was triggered, it will send 3 signals to host(3 different frequency points),and host can receive these signals independently. This anti-interference technology makes our products more competitive in same line.
12. Do the sensors come with the brackets?
Brackets for sensors are not included in package. If necessary, we’ll configure brackets to your order,but it’s better to purchase in your location, common size is OK.
13. What frequency is this transmitting on and do you have GSM notification by text to cellphones for your products?Our frequency 433MHz (FSK+FHSS technology) once sensor was triggered, it will send 3 signals to host(3 different frequency points),and host can receive these signal independently. This anti-interference technology makes our products more competitive in same line.
Host support GSM is :HB-BJQ-560B,HB-G10.
14. But I’m wondering if the sensibility could be adjusted?
Most of our sensors’ sensitivity can be adjusted by customers. Kindly attention that unusual sensitivity will result in false alarm, such as free falling object.
Adjust sensors’ sensitivity as follows:
A. PIR series:there is a Jumper inside--30S/120S(Item No. HB-T201;HB-T205)
B. Infrared detector series(Items those can be hand-made):
Regular sensitivity alarming time:200ms
(HB-T001S4;HB-T001S8;HB-T001Q3+;HB-T001Q4;HB-T001Q6;HB-T001Q8)
Regular sensitivity alarming time:100ms
(HB-T002A8;HB-T002S8;HB-T002S8-D)
Ways to adjust sensibility: restart the sensors(both transmitter and receiver)--long time press the receiver’s on/off button 10 seconds--after one beep--press the receiver’s on/off button 5 times(sensitivity time-200ms);press the receiver’s on/off button 6 times(sensitivity time--100ms)---OK
Ways to rematch the infrared light of the sensors: restart the sensors(both transmitter and receiver)--long time press the receiver’s on/off button 10 seconds--after one beep--press the receiver’s on/off button 4 times---OK
Adjust only by factory: HB-T001Q2;HB-T001Q3
15. Please tell me more about perimeter defense. Total fence length to protect is 2800 meters?
The working principle of our sensors is the same as wired sensor, mainly difference is that we deduct wiring.
Each 100m install one pair of sensor , if any corner or the wall is not straight ,add more sensor.
Remarks:If wireless distance between sensor and host unit exceed 3km,Signal Repeater (HB-ZFQ) is suggested, one Repeater can enlarge wireless distance 3km,currently we support 4 grades, that’s say we can use 4 ZFQ without signal interference, and wireless distance:4-levels transmission X1km/grade=4000m.so more larger defense area is realized.
16.The IR beams works at 433 MHz?, Could work with other alarms also at 433MHz, or only with your alarm host?
The sensors adopt 433MHz (FSK+FHSS technology) once sensor was triggered, it will send 3 signals to host (3 different frequency points),and host can receive these signals independently. This anti-interference technology makes our products more competitive in same line.
Moreover, the code modulation of our detectors is private protocol, so the detectors are hardly directly match up with third-party 433Mhz alarm host.But we have two ways to contact with third party host.
Firstly ,we have switch outputs adapter to convert wireless signal to wired signal to third-party host(on condition that third-party host has wired zones)
Secondly, Send detailed technical parameters of your host to us,we’ll adjust our sensors and pair with your host ,need to mention that will reduce wireless distance and anti-interference function.
17.Are these just sensors or do they act like an alarm system that can report to A central monitoring station for supervision.
We provide the burglar alarm system;
Firstly, we total have 9 sets of alarm host:
Ademco available:HB-BJQ560-A; HB-BJQ560-B; HB-2020C;HB-3030C;HB-G250. Ademco unavailable: HB-MFR;HB-2020A;HB-3030A;HB-G10
Secondly, our sensor will self-check every 2 minutes, if any problem (e.g. low-battery、 invalid、light interference etc.) ,Sensor will immediately report to host.So that user can make solution at first time.
Thirdly, We have other accessories to realize other functions.
Remarks: If wireless distance between sensor and host unit exceed 3km,Signal Repeater (HB-ZFQ) is suggested, one Repeater can enlarge wireless distance 3km,currently we support 4 grades, that’s say we can use 4 ZFQ without signal interference, and wireless distance:4-levels transmission X1km/grade=4000m.so more larger defense area is realized.
18. Our main concern is how to communicate your system to an Out sourced Monitoring Service?
Scheme 1:using the switch outputs to linkage the monitoring service.
Sensors’ Wireless Signal--- host/adapter---- switch outputs interface-- control surveillance device (DVR)
A. HB-MFR, support 4 switch outputs;
mfr connection.jpg
mfr connection.jpg (94.5 KiB) Viewed 9550 times
B. HB-ZJQ-3,support 8 switch outputs;
zjq connection.jpg
zjq connection.jpg (97.47 KiB) Viewed 9550 times
C. If you wanna not only DVR ,but also need LED lights indicate detailed sensor’s zones and locations(as electric map), suggest : HB-G250(engineering host )+HB-LD(linkage module),HB-LD includes : 32 switch outputs and 120 pieces LED lights
engineer host.jpg
engineer host.jpg (549.17 KiB) Viewed 9550 times
Scheme 2: using the internet to linkage the monitoring service.
Network module--surveillance device (suitable for more range project)
HB-G250(engineer host) and HB-WT(network module) is a Unit ,and we offer SDK data.
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Questions of solar power wireless perimeter security system

Unread post by vedard »

network module.jpg
network module.jpg (398.91 KiB) Viewed 9548 times
19. What happens if a bee, or a bird passes through the IR-fence?Bee or bird flying cant trigger the sensor?
Bee of Bird flying will not trigger the sensors
Firstly, if obstacle freely falls and pass through defense area, sensors will not alarm.
Secondly, if 3 infrared holes can’t completely blocked by material, sensors will not alarm.
So, compared with other sensors,our products more effective in reducing false alarm.
20. Works in the light for UK climate?
Firstly, Our solar panel is made of amorphous material. It can convert light to electric even in cloudy or rainy days,without any direct sunshine. While at rainy days ,the solar panel can generate 2mA current to the battery .
Secondly, the static power of our sensors is only 1% of traditional wired
sensor(static power:0.5mA).Besides:the sensors have high-capacity LFP battery inside,can keep the sensors working much more than 15 days without charging.
You may rest assured we have steady customers do this line for many years.
solar beam.jpg
solar beam.jpg (13.7 KiB) Viewed 9548 times
21. What is the extension of the wireless signal of the signal repeater HB-ZFQ?
Without any obstruction, one transponder can enlarge 3KM wireless distance. Currently we support 4 grades transmission, that’s say we can use 4 ZFQ without signal interference.
wireless distance:4 grades transmission X3km/grade=12KM.
So more larger defense area is realized. Reference picture as follows:
signal repeater.jpg
signal repeater.jpg (223.35 KiB) Viewed 9548 times
22. Do you need line of sight or not?
A.PIR series: no need laser pointer, only need install the detectors in the suitable environment and adjust the detect angle is OK.
B. Infrared Barrier series: no need laser pointer, because the infrared distance is only 10m , you just need make sure the Barrier be installed in the same horizontal and vertical plane.
C. Garden Light&Detector series:no need laser pointer, because the infrared distance is only 20m-50m , you just need make sure the Detector be installed in the same horizontal and vertical plane.(you also can use the laser pointer as below)
D.Photoelectric beam sensor series: Infrared distance is 100m. You need to use the laser pointer when the infrared distance exceed 50m
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Questions of solar power wireless perimeter security system

Unread post by vedard »

Remarks :After installation, verify the sensors whether be well mounted.(watch the video and the manuals).
HB-T001Q3+ has LCD calibrator on it
calibrator.jpg
calibrator.jpg (111.54 KiB) Viewed 9547 times
23. Also please confirm if the wireless link is one way or duplex?
Our wireless link is one way, that is to say sensors transmit wireless signal to host , but host cant send signal to control the sensors. While our sensors will self-check every 2 minutes, if any problem (e.g. low-battery、invalid、light interference etc.) ,Sensors will immediately report to host.
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Questions of solar power wireless perimeter security system

Unread post by vedard »












Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Post Reply