Program Alarm Systems Solar Beams Detectors

Business security, commercial security, hotel security, factory security, industry security solution.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Program Alarm Systems Solar Beams Detectors

Unread post by vedard »

Program Alarm System with Solar Beam Sensors
(HB-T001Q2;HB-T001Q3)
1. Press the switch(at the back of the sensor) 1 time to turn on the sensors. (if work normally,the indicator light will on)
2. Keep the Transmitter aligned with the Receiver (if work normally,the indicator lights will blink)
3. Trigger the beam sensors by thick materials(block up all the infrared beams)

(if work normally,the receiver’s light will on) 4.connect the beams to the host(reference to the hosts’ manuals)

(HB-T001Q3+;HB-T001Q4;HB-T001Q6;HB-T001Q8)
【Notice 】HB-T001Q3+ has LCD calibrator,but don’t have on site alarm function
1.Press the switch(at the back of the sensor) 3-10 times to turn on the sensors. (if work normally,the indicator light will on and there are 3-6 “di” beep prompt)
【Notice1 】if press the switch 3 times to turn on: there are 5 seconds alarm voice while the beam sensors be triggered; if 4 times,there are 15 seconds;if 5 times,there are 30 seconds;if 6 times,there are 60 seconds;if 7-10 times,no alarm voice.
All the setting will take effect after 1 hour,within 1 hour,there are 5 seconds alarm voice while the beam sensors be triggered.
2.Keep the Transmitter aligned with the Receiver (if work normally,the indicator lights will blink and there are 6 “dididi” beep prompt) 3.Trigger the beam sensors by thick materials(block up 3 infrared beams) (if work normally,the receiver’s light will on;Notice,if the sensors are in on site alarm mode,the sensors will alarm by the speaker,if in mute mode,no alarm voice ) 4.connect the beams to the host(reference to the hosts’ manuals)
Garden Lights&Beam Sensors
(HB-T002A8)
1.Press the switch(below the LED light)3-10 times to turn on the sensors.
(if work normally,the indicator light will on and there are 3-6“di”beep prompt) 【Notice 】there are 2 switches below the LED light,one is useful,the other one is useless.please press the useful switch to turn on the sensors.you can hear the beep while you press the useful one.
2.Keep the Transmitter aligned with the Receiver
(if work normally,the indicator lights will blink and there are 6“dididi”beep prompt)
You can find the location of the infrared beam by the marks or the indicator light

3.Trigger the beam sensors by thick materials(block up 3 infrared beams) (if work normally,the receiver’s light will on)
Cover all the solar panel of the LED light by thick materials,and the LED light on 4.connect the beams to the host(reference to the hosts’manuals)
(HB-ZFQ)
Total 2 buttons(Status Key and Erase Key)
Total 4 indicators(Run,RF,Learn,Erase)
How to connect detectors or remote controllers to the Repeater:

1. Power on,”Run”light on.
2. Press the Status Key 3 times,”Learn”light on(means the repeater is on learning mode)
3. Trigger the detector or remote controller,”Learn”blink once and a beep prompt. One Repeater can connect 50 pieces detectors or remote controllers,so please connect the other ones by the same way
4. Press “Status Key” once,Exit the learning mode,and”Learn”light off
5. If work normally,“RF”light will blink while you trigger the detectors or remote controllers. How to delete detectors of remote controllers

1. Power on,”Run”light on
2. Press the Status Key 3 times,”Learn”light on
3. Delete one detector(the recent one)–Press”Erase Key”once,and”Erase”light on 1 second.

Delete all the detectors–Press”Erase Key”3 seconds,”Erase”light on and a beep prompt. How to set the grade of the repeater: At present,the repeater has 4 grades,and the grade can be set by the DIP switch;(factory default is grade 1—the”1”switch is on the”ON”direction,the other switches are on the opposite direction;if you want to set the repeater to grade 2,make the”2”switch on the”ON”direction,and the other switches on the opposite direction;So on…)
【Notice 】Make sure the repeater is on Grade 1 when you connect the detectors to it.
Grade 1 Repeater only can forward the signal from the Detectors;Grade 2 Repeater only can forward the signal from Grade 1 Repeater;Grade 3 Repeater only can forward the signal from Grade 2 Repeater;Grade 4 Repeater only can forward the signal from Grade 3 Repeater;But Alarm host can receive the signal from all the repeaters and detectors.
(HB-ZJQ-3)
Total 9 indicators,1 RUN light and 8 zone Lights.
How to connect the detectors
1. Open the enclosure of the adapter,and connect the power cables (If work normally,the Run light blink)
2. Set the DIP switch to connect the detectors;there are 8 DIP switches corresponding 8 zones; For example:connect the detectors to zone 1 Make the DIP switch 1 to ON direction,and the indicator of zone 1 light on,and”Run”light off.(means the Adapter is on learning mode) Trigger the detector,if“Run”blink,connect successfully(each zone can connect 6 pieces detectors at most). Make the DIP switch 1 to figure direction,and the indicator of zone 1 light off,and”Run”light on.(means the Adapter exit the learning mode)
3. If work normally,the light of zone 1 will on for 30 seconds while you trigger the detector(it means the output of zone 1 will keep 30 seconds)
4. Connect the detectors to other zones by the same way. How to delete the detectors

1. Power on the adapter,and“Run”light blink
2. Set the DIP switch to delete the detectors(for example:delete the detector of zone 1) Make the DIP switch 1 to ON direction,and the light of zone1 on,”Run”light off.

3.Delete all the detectors–Press”Delete Key”2 seconds,the light of zone 1 blink.
4.Delete detector of other zones by the same way.
(HB-JHD-2)
Total 4 buttons(On/Off Key;Learning Key;Delete Key;Choose Sound Key) How to connect detectors and remote controllers
1.Press the On/Off Key 3-10 times to turn on the siren. (if work normally, there are 3-6“di”beep prompt)
【Notice1 】if press the On/Off Key 3 times to turn on,the siren will alarm 5 seconds while sensors be triggered;if 4 times,the siren will alarm 15 seconds;if 5 times,the siren will alarm 30 seconds;if 6 times,the siren will alarm 60 seconds;if 7-10 times,no alarm voice.
【Notice2 】If there are 3”di~~”long beep prompt while you turn on the siren,it means the siren is
Low battery or the solar panel was covered by thick materials; All the setting will take effect after 1 hour,within 1 hour,the siren will alarm 5 seconds while sensors be triggered.
2. Press the”Learning Key”once,”Learning Key”light on and a beep prompt (means the siren is on Learning mode)
3. Trigger the sensor or press the arm key of remote controller,”Learning Key”light off and a beep prompt(connect successfully)
4. Connect other sensors or remote controllers by the same way

(press“Learning Key”once,trigger the sensor) How to delete sensors and remote controllers
1. Turn on the Siren.
2. Delete one sensor(the recent one)–Press”Delete Key”once,and”Delete Key”light on 1 second and a beep prompt. Delete all the sensors–Press”Delete Key”3 seconds,”Delete Key”light on and a long beep Prompt.

How to choose the alarm voice(total 2 sounds,one is doorbell,one is Alarm)

1. Turn on the siren

2. Press the”Choose Sound Key”once,the sound you heard is the one you choose.
【Notice 】The operations of Learning,Deleting,Choosing Sound must be operated within 1 hours
after turn on the siren.if after 1 hour,you should restart the siren to operate.
(HB-BJQ-560A/B)
How to connect sensors 1.Press“SETUP”Key 2.Enter password“123456#” 3.Enter password“12*48#” 4.Enter zone number“000#—559#”(total 560 wireless zones) 5.Trigger the sensors
How to connect remote controllers 1.Press“SETUP”Key 2.Enter password“123456#” 3.Enter password“12*48#” 4.Enter zone number“10#—13#”(total 4 remote controller zones) 5.Press the arm key of the remote controller
How to set Phone Number —–total 3 modes:fixed phone mode;mobile phone mode and message mode Fixed Phone Mode: 1.connect the phone line 2.open the fixed phone mode(Setup—123456#—51#1#) 3.enter phone number(10#phone number#;can set total 4 phone numbers.the code is 10#—13#)
Mobile Phone Mode 1.insert the SIM card 2.open the mobile phone mode(Setup—123456#–52#1#) 3.enter phone number(10#phone number#;can set total 4 phone numbers.the code is 10#—13#)
Message Mode
1.insert the SIM card
2.open the message mode(Setup—123456#–53#1#)
3.enter message number(14#message number#;can set total 4 message numbers.the code is 14#—17#)
(HB-G250)with keyboard
How to connect sensors 1.Press“###” 2.Enter password“112233#” 3.Enter password“12*48#” 4.Enter zone number“000#—999#”(total 1000 wireless zones) 5.Trigger the sensors
How to connect remote controllers 1.Press“###” 2.Enter password“112233#” 3.Enter password“12*48#” 4.Enter zone number“10#—14#”(total 5 remote controller zones) 5.Press the arm key of the remote controller
How to set Phone Number 1.connect the phone line 2.Press”###” 3.Enter password”112233#” 3.enter phone number(10#phone number#;can set total 4 phone numbers.the code is
10#,11#,17#,18#)
10#-11#:user’s number code
17#-18#:alarm center number code
4.enter”1#”,open the phone mode
(HB-2020 series and HB-3030 series)
Total 4 buttons(up down left right) How to connect detectors
1. Long time press“UP”key,and power on
2. Press”Left”key to select zone number(total 100 wireless zones,the code is 00–99)
3. Press“UP”key once,a beep prompt
4. Trigger the sensors,if successful,2 beep prompt.
5. Press “Right”key to choose the
6. Press “Down”key to exit setting mode How to connect remote controllers

1.Long time press“Down”key,and power on
2.Press”Left”key to select zone number(total 4 wireless zones,the code is 00–03)
3.Press“UP”key once,a beep prompt
4.Press the arm key of the remote controller,if successful,2 beep prompt.
5.Press“Down”key to exit setting mode How to set phone number 1.connect the phone line and phone ,and then power on 2.long time press the phone set key 3 seconds,and release the phone set key while you heard a
beep prompt 3.handle the phone to set:
Enter password”000000”,a beep prompt
6 user numbers,the code is 11#—16#,for example 11#phone number#
2 alarm center numbers,the code is 17#—18#,for example 17#phone number#
4.enter”0#”to exit setting mode
2014-09-17 09'02'48.jpg
2014-09-17 09'02'48.jpg (20.81 KiB) Viewed 4619 times
reverse aim.jpg
reverse aim.jpg (37.27 KiB) Viewed 4619 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Post Reply