Page 1 of 1

Electrical Fire Monitoring Equipment

Posted: Wed Feb 19, 2020 2:09 pm
by vedard
JB-DH-TC 5600 Electrical Fire Monitoring Equipment (EFME) and DH12A, DH01B, DH230 electrical fire detectors compose an electrical fire monitoring system of loop control communication. An electrical fire monitoring device uses a two-line loop to connect each detector with its own address, which is called communication. This monitoring device supplies power to each sub devices. Alarms information will be sent to control panel through break mode, effective and efficient. Open circuits, short circuits and communication faults of any loop control device will all report to the control panel, which provides an important basis for normal operation of devices and maintenance of follow-up system.

Large-screen character LCD display, through which all information such as alarms, faults or status can be displayed clearly and directly.
The alarming ranges of residual current detectors and heat detectors all can be adjusted widely. They adapt to various situations.
Detectors are addressable, flexible and convenient for commission and installation.
All devices have the interconnection function of fire alarm system with our company.
Maximum 2 loops, with up to 255 electrical fire detectors of a loop.
The enclosure of EFME conforms to the rules of IP30 strictly, with all cracks and louvers smaller than 2.5mm.
Dimension (L×W×H): 360mm×480mm×130mm
[attachment=0]JB-DH-TC5600.jpg[/attachment]

Residual current mutual inductor

Posted: Wed Feb 19, 2020 2:12 pm
by vedard
CTZH61F-2550: connected with detector through non-polarity

Hole diameter: 250*50mm rated operating current for main loop: 630A

Dimensions: 315mm*115mm*45mm

CTZH61F-3260: connected with detector through non-polarity

Hole diameter: 325*60mm rated operating current for main loop: 1000A

Dimensions: 425mm*160mm*60mm

[attachment=0]residual current mutual inductor.jpg[/attachment]

Residual current electrical fire monitoring detector

Posted: Wed Feb 19, 2020 2:14 pm
by vedard
TC-DH01B-J225: hole diameter: 225*56mm rated operating current for main loop: <630A
Dimensions: 296mm*166mm*45mm

TC-DH01B-J325: hole diameter: 325*60mm rated operating current for main loop: <1000A
Dimensions: 445mm*220mm*60mm

Connected with the panel through non-polarity two bus system enables communication and power supply functions.

Electrical programming of the address can be programmed with an electrical programmer in advance making construction commission easy and reliable.

Monitor operation with micro CPU and send module status of normal or alarm to the monitoring device.

Wire: connected with the panel through non-polarity two bus system

[attachment=0]fire monitor system.jpg[/attachment]

Re: Electrical Fire Monitoring Equipment

Posted: Wed Feb 19, 2020 2:15 pm
by vedard
Connected with the panel through non-polarity two bus system enables communication and power supply functions.

Electrical programming of the address can be programmed with an electrical programmer in advance making construction commission easy and reliable.

Monitor operation with micro CPU and send module status of normal or alarm to the monitoring device.

Wire: connected with the panel through non-polarity two bus system

Rated frequency: 50Hz/60Hz

Dimensions: 110mm*92mm*59mm

[attachment=0]fire monitor detector.jpg[/attachment]

combined electrical fire monitoring detector

Posted: Wed Feb 19, 2020 2:17 pm
by vedard
Connected to the panel through non-polarity two bus system which is advanced in technology with reliable communication and easy cabling.

High performance CPU, intelligent algorithm and watchdog adopted enhanced efficient and reliable operation.

Passive contact output inside enables parallel to another one or more loops to form fire alarm linkage mode.

Self-test function to detect whether display components and sounder operate.

Set residual current alarm from 200mA to 1000mA for the residual current mutual indictor. Wide application and high detection accuracy. Address programmable makes construction commission and maintenance easy.

Alarm temperature ranges from 45℃ to 140℃ available for any setup with wide range and high detection accuracy. Set the address and alarm temperature within the detector makes construction commission and maintenance easy.

Dimensions: 210mm*130mm*43mm

[attachment=0]electric fire monitor detector.jpg[/attachment]

how to set up electric fire monitoring detector

Posted: Sat Jan 14, 2023 4:46 am
by vedard

how to wire and encode residual current detector

Posted: Sat Jan 14, 2023 4:48 am
by vedard

how to install electric fire monitoring system in power distribution cabinet

Posted: Sat Jan 14, 2023 4:49 am
by vedard