The home security system
Posted: Tue Jan 15, 2019 9:09 am
1. Alarm Control Panel
Alarm Control Panel is the heart of the complete home security system. It is microwave process system control center. All detectors signal and status will be monitored and identified by alarm control panel. Then the alarm control panel will send feedback, notification and alarm report to set phones or app, message, email.
Install Alarm Control Panel:
1. Choose the place for alarm control panel placement.
At center of all detectors (within the wireless receiving distance 100m). At hidden place. The alarm control panel should be put 0.5 m above the ground to avoid interference.
2. Wire communication line such as telephone line or RJ45 TCP/IP internet line.
3. Connect wired siren to the alarm panel output siren interface if you need it.
4. Connect the AC power supply. Switch on the power, the alarm control panel will start to work. Start to set alarm record or notification phone number etc. for the alarm panel. If no alarm recording message is set, the panel will sound beep every 30seconds.
Setting Alarm Control Panel via below various ways. You can choose the easy way to set it.
1. Set the alarm control panel via built-in LCD keypad on panel.
2. Set the alarm control panel via telephone.
3. Set the alarm control panel via SMS (GSM alarm panel)
4. Set the alarm control panel via IE browser
5. Set the alarm control panel via smart phone app
2.Remote controller
The remote controller has functions of arm, disarm, emergency button.
3. Door contact
Door contact has magnetism part and wireless transmitter part. If the two parts are separated to a defined distance 1.5cm it will trigger alarm.
4. PIR and PIR & MW detector Motion Sensor
There are wide angle PIR and curtain PIR, ceilling mounted PIR three types. PIR infrared sensor is with shortage of easy for interference by air flow and will cause missing alarm for glass and wood blocking. So, Microwave detector is add to PIR for more reliable detection and accurate alarm.
5. Infrared photoelectric beam sensors.
Beams sensors consists of transmitter and receiver as invisible light wall. And it is installed outdoor for first place intrusion prevension and alarm.
Alarm Control Panel is the heart of the complete home security system. It is microwave process system control center. All detectors signal and status will be monitored and identified by alarm control panel. Then the alarm control panel will send feedback, notification and alarm report to set phones or app, message, email.
Install Alarm Control Panel:
1. Choose the place for alarm control panel placement.
At center of all detectors (within the wireless receiving distance 100m). At hidden place. The alarm control panel should be put 0.5 m above the ground to avoid interference.
2. Wire communication line such as telephone line or RJ45 TCP/IP internet line.
3. Connect wired siren to the alarm panel output siren interface if you need it.
4. Connect the AC power supply. Switch on the power, the alarm control panel will start to work. Start to set alarm record or notification phone number etc. for the alarm panel. If no alarm recording message is set, the panel will sound beep every 30seconds.
Setting Alarm Control Panel via below various ways. You can choose the easy way to set it.
1. Set the alarm control panel via built-in LCD keypad on panel.
2. Set the alarm control panel via telephone.
3. Set the alarm control panel via SMS (GSM alarm panel)
4. Set the alarm control panel via IE browser
5. Set the alarm control panel via smart phone app
2.Remote controller
The remote controller has functions of arm, disarm, emergency button.
3. Door contact
Door contact has magnetism part and wireless transmitter part. If the two parts are separated to a defined distance 1.5cm it will trigger alarm.
4. PIR and PIR & MW detector Motion Sensor
There are wide angle PIR and curtain PIR, ceilling mounted PIR three types. PIR infrared sensor is with shortage of easy for interference by air flow and will cause missing alarm for glass and wood blocking. So, Microwave detector is add to PIR for more reliable detection and accurate alarm.
5. Infrared photoelectric beam sensors.
Beams sensors consists of transmitter and receiver as invisible light wall. And it is installed outdoor for first place intrusion prevension and alarm.