Vedard Security Alarm Technical Support

Solar&Wireless Garden Detector
HB-T002S8(single direction) & HB-T002S8-D(dual direction)
Solar&Wireless 8 Beam Barrier+Garden light
Features:
◆ Battery Powered&Solar Charged,no need cables.
◆ Garden Lights turn on automatically at night and turn off automatically at day time.
◆ Multiple Detection Beams(to avoid false alarm--such as small pets).
◆ Dual direction is viable.
◆ Up to 50 meters easy detection range.
◆ 700 KM wireless transmission Range.
◆ Automatic Shielding of the sunlight interference.
◆ Invalid reminder when the beams are not mounted well.
◆ Operating Range:-30°C to 70°C. Technical Parameters
Infrared Detection Range HB-T002A8 20m
HB-T002S8&HB-T002S8-D 50m
Wireless Transmission Range 700m
Beam Quantity 8
Wireless Frequency 433MHz FSK+FHSS
Maximum Trigger Number In 24 Hours ≤200 times
Working Voltage 3.3V
Battery Type Chargeable LiFePO4 Battery
Battery Capacity HB-T002A8 1500mAh
HB-T002S8&HB-T002S8-D 6000mAh
LED Power Consumption HB-T002A8 0.25 W
HB-T002S8&HB-T002S8-D 1W
Infrared Wavelength 940nm±20nm
Solar Panel Power Capability HB-T002A8 0.5W
HB-T002S8&HB-T002S8-D 2W
Working Duration Solar charged for 8-12hours, Garden light can work 20hours continuously
Barriers can work normally all the time no matter for rainy day or sunny days )

Working Temperature Range -30℃~70℃
Weight
HB-T002A8：4.3kg
HB-T002S8：14.7kg; HB-T002S8-D：17.0kg
Dimension HB-T002A8：955×φ160（mm）
HB-T002S8 & HB-T002S8-D：1400×φ150（mm）

How to install solar wireless garden light wall?
Solar wireless garden light wall is combination of wireless infrared grating and solar led lamp to be used for security of garden, courtyard etc. open area outdoor.
Without any wire, just install the light wall on the ground of the garden and place a set of app monitor alarm controller indoor. Moreover, you can place a solar wireless siren strobe on the wall outdoor. Then any intrusion will trigger the light and sound alarm immediately. At the same time, alarm information will be sent to the app. If you link the alarm host to security camera, you will receive intrusion picture from app.
The wireless garden light wall LED lamp will light on at night and light off automatically at day time. Product life time is 8-10 years.
How to install the garden light wall? Does it need a professional to install it?
Wireless security system is designed for easy installation and operation for DIY home security. Below it the steps to install the wireless solar garden light wall.
1.Screw the bracket with the fence to the retainer.The bracket has one end of the connecting wire up.
2.Adjust the direction of the fence to the right angle so that the sender and receiver are aligned.
3.Fix the retainer to the ground with screws.
4.Fix the PC tube on the fixing pin so that the PC tube is in an upright position.
5.Connect the red and black lead connector of the fence to the socket at the bottom of the LED lamp cap, making sure the positive and negative terminals are correct.
6.Turn the LED cap counterclockwise 2-3 times and put it on the PC tube.Turn the metal frame under the LED lamp holder.Tighten by turning clockwise so that the LED lamp head is in an upright position.
Precautions for Calibration?
1. Make sure the fence power is switch on.
2. Make sure the fence is working properly.
3. Fix the fence in installation position and adjust fence position so it is almost flat. Try to make the fence in the same vertical plane and horizontal plane, if there is a deviation can turn the fence left and right.
Method of verifying that the installation is OK
1. Whether the fence light flashes and enters the working state.
2. If two of any group of light holes of the fence are blocked, the fence will not alarm. If three of any group of light holes are blocked, the fence will alarm.

HB-T002 is solar garden light with intrusion detector IR detector. It is installed in garden, park, community square etc. outdoor open space private security protection.
HB-T002 includes 4 parts. They are one pair 8-beams solar infrared grating transmitter and receiver, one pair pole, one pair of PC pipe, one pair solar lamp and one pair pedestal.
There are 4 steps to install the HB-T002 garden lamp with IR detector.
Step 1:
Fix the infrared grating to the pole with screw.
Step 2:
Fix the pole to the pedestal then fix it on the ground.
Step 3:
Put the PC tube
Step 4:
Wire the lamp to the grating and fix it to the pole.

You should need to make some details clear such as infrared grating direction such as wire at upper side. The lamp can keep lighting for 8-10 nights at rainy days. The infrared grating keeps at least 15 days at rainy days.