Addressable fire alarm control panel

Fire alarm system manual download for studying addressable intelligent alarm contorl panel, fire detection system, fire warning, fire evacuation system.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Addressable fire alarm control panel

Unread post by vedard »

Addressable fire alarm control panel works with printer, network communication card, repeater panel, smoke alarm, heat detector, gas sensor, manual call point, siren strobe. The complete alarm system can automatic trigger fire fighting system, and gas extinguisher, Exhaust fan for Smoke exhaust.
panel MN300.pdf
(1.77 MiB) Downloaded 625 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Addressable fire alarm control panel

Unread post by vedard »

addressable-fire-alarm.jpg
addressable-fire-alarm.jpg (116.54 KiB) Viewed 10665 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Re: Addressable fire alarm control panel

Unread post by vedard »

fire alarm system.JPG
fire alarm system.JPG (54.74 KiB) Viewed 10635 times
address fire alarm.JPG
address fire alarm.JPG (63.21 KiB) Viewed 10634 times
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Jim
Posts: 88
Joined: Sat Oct 31, 2020 1:01 pm

Setting of ring-type bus-line short circuit isolators

Unread post by Jim »

How to add the bus-line short circuit isolators?
We make clear explain as below with diagrams.
Note:
1. We take smoke and heat detectors as examples in the picture.
Only the alarm bus-line is drawn and the power cord is omitted.
2. In Figure 3, the bus-line passes through the fire partitions, and if no equipment is connected in the fire partition, a short-circuit isolator may not be installed in the fire partition.The bus short-circuit isolator of annular structure can be arranged on the side of fire partition 1 or fire partition 2.
3. The number of address occupied by the bus short-circuit isolator products of some equipment manufacturers shall be calculated according to the nominal address number of equipment manufacturers.
4. The bus short-circuit isolator can be placed in the module box or installed near the wall along the road with the base distance of 2.2m.When installed in the ceiling, the bottom should be close to the ceiling 0.2m apart, and the ceiling should be repaired and marked clearly.Dendritic bus short-circuit isolators can also be centrally located in weak current silos.
5. Bus short-circuit isolators with ring structure and tree structure are generally not universal.
6. If the fire detector has its own isolation function, the bus short-circuit isolator can no longer be set up separately.
7. Whether the bus loop adopts tree structure or ring structure shall be determined by the designer and the corresponding products shall be selected and matched.
Attachments
ring type bus-line isolation module installation.png
ring type bus-line isolation module installation.png (19.83 KiB) Viewed 8210 times
ring shape bus-line fire alarm isolation module wiring.png
ring shape bus-line fire alarm isolation module wiring.png (17.59 KiB) Viewed 8210 times
ring shape addressable fire alarm system.png
ring shape addressable fire alarm system.png (82.58 KiB) Viewed 8210 times
Guide and supplier for fire alarm systems.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

LPCB approved Addressable fire alarm system

Unread post by vedard »

Commercial security and industry security addressable fire alarm system with LPCB certificate.
Content:
1. Automatic Fire Alarm System
2. Gas fire extinguishing control system
3. Graphic Display unit
4. Explosion-proof system
5. Intrinsically safe system
6. Combustible gas alarm control system
7. Aspirating Smoke Detection and alarm system
8. Smart safety home security system
9. Smart fire protection system
Attachments
TC5000 addressable fire alarm system.pdf
(4.18 MiB) Downloaded 469 times
Last edited by vedard on Thu Dec 10, 2020 12:00 pm, edited 1 time in total.
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Jim
Posts: 88
Joined: Sat Oct 31, 2020 1:01 pm

Addressable fire detectors manual

Unread post by Jim »

Instruction manual of input module
Use and operation Encoding operation: you can use our company's hand-held encoder to live coding. When encoding, connect the two clips of the encoder to the two terminals of the linkage, open the handheld encoder power, enter the address code to be written (address code range must be: 1-242, the address code for the same loop is unique). Press the "write code" button, if encoding is successful, the encoder will display the address number after sending the address code. If failed, the encoder will display “FAL” after sending the address code.For details on the steps and methods of encoding, refer to the " Handheld Encoder User's Manual".
F. Note 1. The alarm function test of smoke detector should be performed every six months. 2. When the controller detects the cleaning forecast, please send the number of smoke detectors back to the company for cleaning, in order to avoid false or false positives, resulting in unnecessary losses.
Attachments
Manual for addressable fire devices.pdf
(372.78 KiB) Downloaded 416 times
Guide and supplier for fire alarm systems.
vedard
Posts: 837
Joined: Wed Dec 05, 2018 12:27 am

Hand held programmer manual

Unread post by vedard »

Hand held programmer is important device for addressable fire alarm system. With it, programming and reading code of addressable fire alarm system is easy.
Attachments
5023 Hand Held Programmer.pdf
(226.75 KiB) Downloaded 459 times


Last bumped by vedard on Sat Mar 06, 2021 8:20 am.
Shop Focus brand wireless alarm, HB solar power alarm, HST fire alarm at https://www.vedardalarm.com
Post Reply