Fire Alarm and automatic panel operation training
Posted: Wed Feb 27, 2019 2:28 pm
Fire Alarm and automatic panel Introduction:
The main parts of automatic fire alarm machine consist of alarm device, keyboard, linkage control unit, linkage power supply disk, fire telephone host, fire emergency broadcasting and so on.
Alarm Device:
1. LCD screen: display alarm type, alarm time, alarm address code, alarm equipment name, alarm location.
2. Printer: Print alarm information of alarm equipment, alarm type, alarm time, alarm address code.
3. Indicator area: When the host receives information including feedback, alarm, system status, the corresponding indicator lights on.
Keyboard:
Mute, press "mute" button, the mute indicator lights on, the speaker stops sounding. Next time alarm triggers, it will sounds.
Reset, Press "reset" button after fire alarm has been dealt or system fault has been dealt. Password is required to confirm. After reset, all the fire alarm, feedback or fault displaying will be cleared and the system enters into normal monitor status.
Bypass button. Bypass is used to temporarily isolate the fault part of system. Fault alarm will not be triggered after bypass. During system bypass time, more partrol time is needed until fault part is repaired or replaced. Unbypass should be used to resume the system.
start button: the equipment controlled by the panel can be started or stopped by start button on panel or linkaged device. If using panel to control it, the controlled equipment type and address is required to input. If using linkage device to control it, it is linked and can fast drive it. No matter which way is used, the control panel should be under "manual enabled" status to effect the function.
Automatic and Manual control switch. Manual control means the peripheral equipment will be drived by pressing of start button. Automatic control means the peripheral equipment will be drived automatically by system. It is best to use manual controlling for the bus-model fire alarm system if someone is on duty.
Record check: press record check button, it will display recorded alarm information. If the printer is under printing status when you browsing the record, you can select record to print. The alarm record should be recorded in Fire Duty Diary with details including alarm cause, dealing result and partrol person.
Fire telephone system
Check the fire telephone system communication between fire phone host and fire phone extension. Firstly, pick up the fire phone host receiver, input password, press the corresponding extension selection key(key 2), the corresponding fire extension phone rings, relative staff picks up the receiver and talk. Voice communication should be good. Secondly, Fire extension phone calls to fire host phone and talks. The voice communication should be good.
Fire Emergency Broadcasting System
Steps for operating fire broadcasting system
1. Start the broadcast module
2. Pick up the microphone and select the area of notification needed on the radio distribution disk
3. Press the Speech Button on the Microphone to broadcast
The main parts of automatic fire alarm machine consist of alarm device, keyboard, linkage control unit, linkage power supply disk, fire telephone host, fire emergency broadcasting and so on.
Alarm Device:
1. LCD screen: display alarm type, alarm time, alarm address code, alarm equipment name, alarm location.
2. Printer: Print alarm information of alarm equipment, alarm type, alarm time, alarm address code.
3. Indicator area: When the host receives information including feedback, alarm, system status, the corresponding indicator lights on.
Keyboard:
Mute, press "mute" button, the mute indicator lights on, the speaker stops sounding. Next time alarm triggers, it will sounds.
Reset, Press "reset" button after fire alarm has been dealt or system fault has been dealt. Password is required to confirm. After reset, all the fire alarm, feedback or fault displaying will be cleared and the system enters into normal monitor status.
Bypass button. Bypass is used to temporarily isolate the fault part of system. Fault alarm will not be triggered after bypass. During system bypass time, more partrol time is needed until fault part is repaired or replaced. Unbypass should be used to resume the system.
start button: the equipment controlled by the panel can be started or stopped by start button on panel or linkaged device. If using panel to control it, the controlled equipment type and address is required to input. If using linkage device to control it, it is linked and can fast drive it. No matter which way is used, the control panel should be under "manual enabled" status to effect the function.
Automatic and Manual control switch. Manual control means the peripheral equipment will be drived by pressing of start button. Automatic control means the peripheral equipment will be drived automatically by system. It is best to use manual controlling for the bus-model fire alarm system if someone is on duty.
Record check: press record check button, it will display recorded alarm information. If the printer is under printing status when you browsing the record, you can select record to print. The alarm record should be recorded in Fire Duty Diary with details including alarm cause, dealing result and partrol person.
Fire telephone system
Check the fire telephone system communication between fire phone host and fire phone extension. Firstly, pick up the fire phone host receiver, input password, press the corresponding extension selection key(key 2), the corresponding fire extension phone rings, relative staff picks up the receiver and talk. Voice communication should be good. Secondly, Fire extension phone calls to fire host phone and talks. The voice communication should be good.
Fire Emergency Broadcasting System
Steps for operating fire broadcasting system
1. Start the broadcast module
2. Pick up the microphone and select the area of notification needed on the radio distribution disk
3. Press the Speech Button on the Microphone to broadcast